Masonry Contractors in Biloxi, Mississippi
Masonry, brick, and stone work.
Biloxi is a casino resort city with hurricane recovery driving strong roofing and contractor demand.
Masonry in Biloxi must resist humidity, salt air, and hurricane forces. Use proper mortar and sealers to fight the moisture intrusion and efflorescence common in Mississippi, and choose corrosion-resistant ties and reinforcement near the coast. Block and brick offer strong wind resistance, but flashing and weep holes are essential to drain wind-driven rain. A local mason should know coastal detailing that keeps salt and water from breaking down the wall over time.
1
Listed contractors
$3k–$20k
Typical cost
What to look for when hiring a masonry contractor
- ✓Ask about the contractor's specific experience with your project type (chimney vs. stone veneer vs. flatwork).
- ✓Request references or photos of similar completed projects.
- ✓Verify the bid specifies materials: brick type or stone species, mortar mix, any waterproofing.
- ✓Confirm they handle required building permits for structural masonry work.
- ✓Ask about their approach to temperature and weather conditions for exterior applications.
- ✓Get a workmanship warranty in writing covering mortar joint failure or settling.
Masonry contractors in Biloxi(1 listed)
How much does masonry cost in Biloxi?
Masonry costs vary widely by project type. Brick repointing runs $300–1,000 per 100 square feet of wall area. Chimney repair ranges from $500–2,500 for minor tuckpointing to $4,000–10,000 for major rebuilding or liner replacement. Brick veneer installation: $15–30 per square foot installed. Natural stone veneer: $20–45 per square foot; manufactured stone veneer $12–25. Concrete flatwork: $6–12 per square foot standard; stamped or exposed aggregate adds $4–8 per square foot. Block retaining walls: $15–30 per square foot of face area. Foundation crack repair: $500–2,000 for epoxy injection; $10,000+ for structural work. In cold climates, schedule exterior masonry in late summer or early fall. Always get multiple written estimates specifying material type, mortar mix, waterproofing approach, and workmanship warranty.
Masonry contractors in Biloxi — FAQ
How many masonry contractors are in Biloxi?
EdgeLocal lists 1 licensed masonry contractor in Biloxi, Mississippi. All listings are sourced from state licensing registries.
What is the average rating for masonry contractors in Biloxi?
Masonry contractors in Biloxi are listed on EdgeLocal with ratings sourced from Google Business profiles. Use the directory to compare rated contractors near you.
Do masonry contractors in Biloxi need to be licensed?
Yes. Mississippi requires masonry contractors to hold a valid state license. Always verify a contractor's license is current and in good standing before signing any contract or allowing work to begin.
How do I find a reliable masonry contractor in Biloxi?
Start by verifying the contractor holds a valid Mississippi license. Check their Google rating and read reviews. Get at least three written estimates. Confirm they carry general liability and workers' compensation insurance. Ask for references from recent Biloxi jobs.
General Masonry FAQs
How much does masonry work cost?
Masonry costs depend heavily on the type of work. Brick veneer installation runs $15–$30 per square foot installed. Stone veneer (manufactured or natural) costs $20–$45 per square foot installed. Brick pointing (repointing deteriorated mortar joints) typically runs $500–$2,000 for a standard chimney or section of wall. Chimney repair ranges from $300–$800 for minor tuckpointing to $2,500–$6,000 for major rebuilds or liner replacement. Poured concrete flatwork (driveways, patios, sidewalks) runs $6–$12 per square foot. Concrete block foundation repair varies significantly by scope—minor crack injection runs $500–$2,000, while major foundation work can cost $5,000–$25,000 or more. In cold climates, masonry contractors typically schedule exterior work in early fall before freeze-up or in late spring for better availability. Always get multiple bids and make sure each bid specifies material type, mortar mix, and labor scope.
Where do I find masonry contractors near me?
Search EdgeLocal for "masonry," "mason," or "brick" with your zip code to find local masonry and stonework contractors. Masonry contractors handle brick laying, stone veneer, block foundation repair, chimney work, patio installation, retaining walls, and concrete flatwork. Masonry contractors are typically registered as general or specialty contractors with their state's contractor licensing authority. When hiring a mason, look for contractors with experience in your specific project type—chimney repair requires different expertise than decorative stone veneer or a poured concrete patio. Ask for references from similar past projects and review their EdgeLocal ratings. For structural masonry work, verify that the contractor pulls the required building permits. Get at least two to three estimates that each specify materials (brick type, mortar mix, stone species), labor scope, timeline, and workmanship warranty.
How do I know if my chimney needs repointing or major repair?
Tuckpointing (repointing) is needed when mortar joints between bricks show visible crumbling, cracking, gaps, or a recessed surface more than ¼ inch deep. Left unaddressed, deteriorated mortar allows water infiltration that can freeze and expand in winter, accelerating brick damage and eventually causing structural failure. Major chimney repair is needed when bricks are visibly spalling (flaking or crumbling), when there is significant leaning or separation of the chimney from the house, when the chimney crown is cracked or missing, or when a masonry liner inspection reveals cracks that allow flue gases to escape. A CSIA-certified chimney sweep can provide a camera inspection of the liner and a detailed assessment of both the exterior masonry and the flue. Most reputable masonry contractors offer chimney inspections and can differentiate between minor tuckpointing and more extensive rebuilding work.
What is the difference between tuckpointing and repointing?
Tuckpointing and repointing are often used interchangeably, but they describe slightly different techniques. Repointing (also called pointing) means removing the deteriorated mortar to a depth of ¾–1 inch and filling in fresh mortar to seal and stabilize the joint. It restores the mortar to its original appearance. Traditional tuckpointing uses two contrasting colors: a mortar fill that closely matches the brick color, with a thin, colored putty "tuck" applied on top to create the illusion of fine, sharp joints—a technique common in older European brickwork and on high-end historic restorations. For most residential repair projects, repointing is the correct term and the appropriate technique. Either way, the key quality factors are: matching the new mortar strength to the original (softer historic mortar requires a lime-based mix, not modern Portland cement), proper joint depth before repointing, and thorough weather protection during curing.
How do I waterproof or seal brick and stone after masonry work?
Sealing masonry after installation protects against water infiltration, efflorescence (white mineral salt deposits), and freeze-thaw damage. Clear penetrating sealers are the most common choice — they do not change the appearance of the masonry and allow water vapor to escape, preventing moisture from being trapped inside the wall. Film-forming sealers create a visible coating and offer stronger protection but can trap moisture if not properly specified for the substrate. For chimneys, a crown sealer on the concrete cap and a flexible masonry waterproofer on the brick are two separate products with different functions. Tuckpointed sections should cure for at least 28 days before sealing. Most masonry sealers need to be reapplied every 3–5 years depending on exposure and product type.